Code-3 PSE LED F12 12 Output Flashers Bedienungsanleitung PDF herunterladen

12 OUTPUT LED FLASHER MULTI-PATTERN

PSELEDF12

ELECTRICAL SPECIFICATION

Input Voltage Range +10 Vdc to +16 Vdc

Output Drive Current 3 Amps per Output

Operating Temperature -40 C to +85 C

Flash Patterns Quint, Quad, Triple, Double,

180 fpm Alternating Single,

120 fpm Alternating Single,

120 fpm Simultaneous Single,

90 fpm Alternating Single,

90 fpm Simultaneous Single,

75 fpm Alternating Single,

75 fpm Simultaneous Single,

Cycle Flash

Sweep (Lightbar version only)

Fast Random

Output Drive Method Low-side switched

Pattern Control Method 1 Serial Programming

input, 3 Progressive Operation

mode inputs, Front & Rear

Cutoff inputs

Standby Current <10mA @ 12.8 Vdc

Reverse Polarity Protection Yes

Short Circuit Protection Yes

Thermal Protection Yes

MECHANICAL SPECIFICATIONS

Weather resistance Potted to protect circuitry, but not

waterproof

Dimensions 6.0" x 3.6" x .75"

WARNING

This device is intended for use with LED Lights ONLY!! Use of this product on an Incandescent, Halogen or

any light source other than LED's may damage the unit and void the warranty.

The use of this or any warning device does not insure that all drivers can or will observe or react to an

emergency warning signal. Never take the right-of-way for granted. It is your responsibility to be sure you

can proceed safely before entering an intersection, driving against traffic, responding at a high rate of

speed, or walking on or around traffic lanes.

The effectiveness of this warning device is highly dependent upon correct mounting and wiring. Read and

follow the manufacturer's instructions before installing or using this device. The vehicle operator should

insure daily that all features of the device operate correctly. In use, the vehicle operator should insure the

projection of the warning signal is not blocked by vehicle components(i.e., open trunks or compartment

doors), people, vehicles, or other obstructions. This equipment is intended for use by authorized personnel

only. It is the user's responsibility to understand and obey all laws reguarding emergency warning devices.

The user should check all applicable city, state and federal laws and regulations.

Code 3, Inc., assumes no liability for any loss resulting from the use of this warning device. Proper

installation is vital to the performance of this warning device and the safe operation of the emergency

vehicle. It is important to recognize that the operator of the emergency vehicle is under psychological and

physiological stress caused by the emergenct situation. The warning device should be installed in such a

manner as to A) Not reduce the output performance of the system, B) Place the controls within convenient

reach of the operator so that he can operate the system without losing eye contact with the roadway.

Emergency warning devices often require high electrical voltages and/or currents. Properly protect and use

caution around live electrical connections. Grounding or shorting of electrical connections can cause high

current arcing, which can cause personal injury and/or severe vehicle damage, including fire.

PROPER INSTALLATION COMBINED WITH OPERATOR TRAINING IN THE PROPER USE OF EMERGENCY

WARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY OF EMERGENCY PERSONNEL AND THE PUBLIC.

Figure1

WARNING

This Flasher is NOT waterproof!! This unit must

be installed in a location protected from the

environment.

The device is designed to flash Code 3, Inc. 12 volt

LED-EX Lights up to 3 amps load per output. DO NOT

connect more than a 3 amp load(two single LED-EX

equivalent) to the output. Doing so will shut the unit

down to prevent damage to the Flasher.

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - PSELEDF12

112 OUTPUT LED FLASHER MULTI-PATTERNPSELEDF12ELECTRICAL SPECIFICATIONInput Voltage Range +10 Vdc to +16 VdcOutput Drive Current 3 Amps per OutputOper

Seite 2

2Output Designation:J4,J5 : PS Front J6 : PS Rear CornerJ2,J3 : DS Front J1 : DS Rear CornerJ7,J12 : PS Rear J8 : PS Front CornerJ9,

Seite 3

32. Remote LED Flasher version p/n T08097:This version has the same connector interface as the Low Profile version, except that this version utilizesd

Seite 4 - Flash - Pattern Programming

4Flash - Pattern ProgrammingA. Lightbar Version:The desired flash pattern for any of the progressive operation modes 1, 2, & 3 can be programmed a

Seite 5 - WARNING!

5EXTENSION CABLE WIRINGMALE AMP CONNECTOR(to terminate the LED-EX Lighthead harness)Insert wires with male pins intothe proper locations in the m

Seite 6

6NOTES:

Seite 7

7NOTES:

Seite 8 - WARRANTY

Kommentare zu diesen Handbüchern

Keine Kommentare

Code-3 PSE LED F12 12 Output Flashers Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Code-3 PSE LED F12 12 Output Flashers herunter. Code 3 PSE LED F12 12 Output Flashers User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Code-3 PSE LED F12 12 Output Flashers