6
This Product contains high intensity TriCore® or Torus devices. To prevent eye
damage, DO NOT stare into light beam at close range.
WARNING!
Flash Patterns
STANDARD LIGHT HEAD FLASH PATTERNS
PATTERN NO PATTERN DESCRIPTION
1 FAST ALTERNATING QUAD FLASH 100ms/25ms
2 PICKET FENCE SINGLE FLASH 200ms/25ms
3 ALTERNATING SINGLE FLASH 200ms/25ms
4 PICKET FENCE QUAD FLASH 100ms/25ms
5 PICKET FENCE SIX FLASH 75ms/25ms
6 SLOW ALTERNATING QUAD FLASH 150ms/50ms
7 SLOW ALTERNATING SIX FLASH 125ms/25ms
8 FAST ALTERNATING SIX FLASH 75ms/25ms
9 VARIABLE RATE PICKET FENCE, SINGLE FLASH
10 ALTERNATING QUAD FLASH, 80 FPM, NFPA COMPLIANT
11 CYCLE FLASH
12 SIMULTANEOUS QUAD FLASH, 75 FPM, NFPA COMPLIANT
Flash Pattern Changes
ARROWSTIK FLASH PATTERNS
PATTERN NUMBER PATTERN DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
Building, Fast Speed
Building, Medium Speed
Building, Slow Speed
Building, 3 Flash, Fast Speed
Building, 3 Flash, Medium Speed
Building, 3 Flash, Slow Speed
Traveling Ball, 3 Flash, Fast Speed
Traveling Ball, 3 Flash, Medium Speed
Traveling Ball, 3 Flash, Slow Speed
Build/Collapse, Fast Speed
Build/Collapse, Medium Speed
Build/Collapse, Slow Speed
TriCore® or Torus™ Light Head Flash Pattern
To change the ash patterns of the TriCore® or Torus™ Light Heads for either Standard or ArrowStik® patterns,
activate the Light Bar in Level 1 or any ArrowStik mode and then momentarily touch the Green (Pattern Select) wire
to +power. Repeating this procedure allows the operator to cycle through the numerous ash patterns offered until
the desired pattern is achieved. Repeat for all modes as needed.
Note: Each ArrowStik mode must be set individually.
To reset the ash patterns to the factory default, activate the Light Bar in Level 1 or any ArrowStik mode and then
hold the Green (Pattern Select) wire to +power for approximately 4 seconds.
Note: 1-Resetting the Standard patterns will reset only the Level 1 ash patterns
2-Resetting the ArrowStik patterns in any ArrowStik mode will reset all ArrowStik ash patterns.
6 HEAD ARROWSTIK® W (2) OUTER LIGHT HDS FLASHING ALTERNATELY
The WingMan™ can be congured as a 6 or 8 head ArrowStik. To change the WingMan from an 8 head ArrowStik to a 6 Light
Head conguration with the (2) Outboard Light Heads ashing alternately, remove the mounting screws that attach the Wing-
Man's Cover to the Outer Panel to gain access to the printed circuit board inside (see the exploded view on page 7). Move the
Shunt Option Jumper (JP1) on the printed circuit board to the "OPTION JP1" position as shown below. When congured for a 6
head operation the (2) Outboard Light Heads will alternate during any ArrowStik mode. Carefully replace the WingMan's Cover
over the Outer Panel and replace the Cover Mounting Screws.
Note: Be extremely careful to replace the wiring such that you don't pinch a wire when you
replace the WingMan's Cover. Test the unit to be sure that it works properly.
<---------------"OPTION JP1" Jumper Position
(8 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern