Code-3 Series 700 Flashers Bedienungsanleitung PDF herunterladen (Seite 1)

Installation Guide

for Model 700 Flasher

General Description

The Code 3 Model 700 Alternating Flasher uses an electronic timing circuit to control two specially

designed flasher relays. The unit is totally weather resistant and may mounted anywhere on the vehicle

away from heat sources and direct water splashes, using either the mounting tabs at each end or the

mounting hole through the device. Outputs 1 and 2 are capable of handling up to 100 watts (8 amps.)

each. Model 700 flasher can be used as a Headlight Flasher, a non daytime running lights hot side

switching flasher or as alightbar flasher.

Terminal Functions

Terminal A - Output 1: 100 watts (8 amps.) maximum load.

Terminal B - Output 2: 100 watts (8 amps.) maximum load.

Terminal c - Flasher On: Activated by + 12VDC.

Applying +12VDC to this terminal through a user supplied switch activates the alternating flash of loads 1

and 2.

Terminal D - Input: To Battery Positive.

Supplies +12VDC to outputs 1 and 2. A user supplied fuse should be installed to protect the outputs. Use

at least 14AWG wire and 20 amp fuse.

Terminal E - To Battery Negative.

Provides ground for the unit. For best results connect directly to the negative terminal of the battery.

Terminal F - Steady burn: Activated by +12VDC

Applying +12VDC through a user supplied switch turns both outputs on simultaneously. When removed,

the unit will function normally. This feature will override all other functions.

Terminal G - Pause: Activated by +12VDC.

Applying +12VDC through a user supplied switch turns both outputs off simultaneously. When removed,

the unit will function normally.

Operation as a Headlight Flasher (12v Operation 0nly)

To operate the Model 700 as a headlight flasher, follow the wiring instructions of Diagram 1. Also, refer to

the instruction chart on page 2 for wire colors and their location for a particular vehicle.

To operate, apply +12VDC to terminal C through a user supplied switch. This will start the alternating

flash. Now, turn on the vehicle's low beam headlights. The low beam lights should burn steadily. Now.

activate the highbeam switch. High beam lights should now be on. If you do not get these results, recheck

all connections listed above.

If you wish the high beams to continue to flash while the low beams are on, do not connect Terminal G.

See Diagram 1 for additional help.

DIAGRAM 1: WIRING DIAGRAM FOR HEAD LIGHT

FLASHER INSTALLATION

- +

DIAGRAM 2: 24v OPERATION

1 2 3 4 5 6 7 8 9

Inhaltsverzeichnis

Seite 1 - Installation Guide

1Installation Guidefor Model 700 FlasherGeneral DescriptionThe Code 3 Model 700 Alternating Flasher uses an electronic timing circuit to control two s

Seite 2 - PRODUCT RETURNS

2Operation as a Light Bar FlasherTo operate the Model 700 as a light bar flasher, jumper Terminal C to Terminal D and connectthese to +12VDC in the ba

Seite 3 - & OPERATION

1INSTALLATION& OPERATIONMANUALMODELS 710 & 711MULTIPLE MODEFLASHERSContents:Introduction ...

Seite 4 - Installation & Mounting

2IntroductionThe Code 3® Model 710 and 711 multiple mode flashers use an electronic timing circuit to control twospecially designed flasher relays. B

Seite 5 - WARNING!

3!WARNING!Larger wires and tight connections will provide longer service life for components. For highcurrent wires it is highly recommended that ter

Seite 6 - Flash Mode 1 Installation

4BATTERYÑ+20 AMPFUSE14 AWG MIN.FLASHER ON - MODE #1RIGHT HIGH BEAMLEFT HIGH BEAMVEHICLE'S HIGH BEAM SWITCHVEHICLE'S LOW BEAM SWITCHHGFEDCBAC

Seite 7 - Mode 2 Test

5FIGURE 2Testing the Circuits for Headlight Flasher Modes 1 and 2.Mode 1 Test1) Install the 20 amp. fuse in the in-line fuse holder.2) Turn ON the swi

Seite 8

NOTES

Seite 9

Public Safety Equipment, Inc.10986 N. Warson RoadSt. Louis, Missouri 63114-2029—USAPh. (314) 426-2700 Fax (314) 426-1337www.code3pse.comRevision 9, 7

Kommentare zu diesen Handbüchern

Keine Kommentare

Code-3 Series 700 Flashers Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Code-3 Series 700 Flashers herunter. Code 3 Series 700 Flashers User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Code-3 Series 700 Flashers Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Code-3 Series 700 Flashers herunter. Code 3 Series 700 Flashers User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Code-3 Series 700 Flashers