Code-3 RX 2700CC Bedienungsanleitung PDF herunterladen (Seite 8)

Selecting the ArrowStik™ Pattern

As mentioned previously, the Central Controller will come from the factory with the ArrowStik patterns set in the default conguration which, is the

Building 7HD conguration. See Table 2. The current conguration can be determined by observing the operation of the ArrowStik™ unit. Note that

Flash Signal Patterns marked with an Asterisk "*" are available in Fast, Medium or Slow ash rate.

Note: It will be important to observe the operation of the ArrowStik unit during the programming procedure while stepping through the

signal options. Signals are available for 6, 7 or 8 head congurations. Also refer to the trafc directing signal options in Table 2 for the

following procedure.

The Pattern Select wire is the BLK/RED wire in the sixteen conductor lightbar control cable and is activated by momentarily touching the wire to

+power.

STEP 1

Power-up the lightbar and select the ArrowStik mode that you wish to program (LEFT, CENTER-OUT, RIGHT or FLASH ).

STEP 2

Observe the ArrowStik operation and determine the current mode. Determine what pattern and conguration the control head is currently in, if not in

the factory default.

Once the pattern / conguration has been determined, proceed to Step 3.

STEP 3

Refer to Table 2, on Page 8. This table shows the available patterns for each mode and their order in program memory. Notice that for the LEFT,

CENTER-OUT and RIGHT positions there are four (4) pattern choices; Building, Building with 3 Flash for the end lights, Build/Collapse with 3 ash

for the end lights, and Build/Collapse with no end ash, three (3) congurations for the number of heads; 6, 7, or 8 HD and three (3) speeds; Fast,

Medium and Slow. There are a total of twelve possible selections for each conguration of light heads and then you return to the top selection,

Building 8 HD, Fast. Starting from the rst pattern in Table 1 you can step through each pattern, ( 1-4 ) for an 8HD, ( 5-8 ) for a 6HD and ( 9-12 ) for

a 7 HD conguration, by momentarily holding the Pattern Select wire to +power for 1-2 sec, until the Arrowstik™ LEDs stop, and then releasing. This

will step to the next pattern in Table 2 for the selected mode. The new pattern is automatically stored each time.

Note: HOLD the Pattern Select wire to +POWER source until you are sure Arrowstik™ pattern has changed (~1 second) before releasing

the wire from the +POWER source. To restore the Factory Default Arrowstik™ patterns, hold the PGM wire on the +POWER source for

~four (4) seconds .

When the FLSH function is selected, the same procedure applies as above, but you will notice in Table 2 that the patterns are not grouped by the

number of heads or outputs. These are trafc warning patterns and work equally well for any conguration of LED modules. There are a total of

nine ( 1-9 ) trafc warning patterns available. Flash patterns marked with an asterisk "*" may also be selectable in Fast, Medium or Slow ash rate.

When you have programmed the desired pattern for the selected function, proceed to Step 4.

STEP 4

Select another mode and repeat the previous steps until all of the functions are programmed as desired.

Mode LEFT CENTER-OUT RIGHT FLASH

Building 8HD, Fast

Building 8HD, 3 Flash

Traveling Ball 8HD, 3 Flash

Build/Collapse 8HD

Building 8HD, Fast

Building 8HD, 3 Flash

Traveling Ball 8HD, 3 Flash

Build/Collapse 8HD

Building 8HD, Fast

Building 8HD, 3 Flash

Traveling Ball 8HD, 3 Flash

Build/Collapse 8HD

Quad Flash Standard

Simultaneous Flash*

Quad Fl Simultaneous

Even/Odd Flash*

Building 6HD, Fast

Building 6HD, 3 Flash

Traveling Ball 6HD, 3 Flash

Build/Collapse 6HD

Building 6HD, Fast

Building 6HD, 3 Flash

Traveling Ball 6HD, 3 Flash

Build/Collapse 6HD

Building 6HD, Fast

Building 6HD, 3 Flash

Traveling Ball 6HD, 3 Flash

Build/Collapse 6HD

Quad Fl Even/Odd

Left/Right Flash*

Quad Fl Left/Right

Traveling Ball Flash*

(Factory Default) 9.

10.

11.

12.

Building 6HD, Fast

Building 6HD, 3 Flash

Traveling Ball 6HD, 3 Flash

Build/Collapse 6HD

Building 6HD, Fast

Building 6HD, 3 Flash

Traveling Ball 6HD, 3 Flash

Build/Collapse 6HD

Building 6HD, Fast

Building 6HD, 3 Flash

Traveling Ball 6HD, 3 Flash

Build/Collapse 6HD

Standard Flash*

Trafc Directing / Trafc Warning Pattern Options

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Code-3 RX 2700CC Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Code-3 RX 2700CC